NetUdpServer 类

实例化一个默认的对象
Instantiate a default object

获取或设置服务器是否支持IPv6的地址协议信息
Get or set whether the server supports IPv6 address protocol information

服务器引擎是否启动
Whether the server engine is started

组件的日志工具，支持日志记录，只要实例化后，当前网络的基本信息，就以DEBUG等级进行输出
The component's logging tool supports logging. As long as the instantiation of the basic network information, the output will be output at DEBUG

获取或设置服务器的端口号，如果是设置，需要在服务器启动前设置完成，才能生效。
Gets or sets the port number of the server. If it is set, it needs to be set before the server starts to take effect.

获取或设置一次接收时的数据长度，默认2KB数据长度

获取或设置客户端的Socket的心跳时间信息，这个是Socket底层自动实现的心跳包，不基于协议层实现。默认小于0，不开启心跳检测，如果需要开启，设置 60_000 比较合适，单位毫秒
Get or set the heartbeat time information of the Socket of the client. This is the heartbeat packet automatically implemented by the bottom layer of the Socket, not based on the protocol layer. The default value is less than 0, and heartbeat detection is not enabled. If you need to enable it, it is more appropriate to set 60_000, in milliseconds.

网络类的身份令牌，在hsl协议的模式下会有效，在和设备进行通信的时候是无效的
Network-type identity tokens will be valid in the hsl protocol mode and will not be valid when communicating with the device

异步传入的连接申请请求
Asynchronous incoming connection request

检查当前的头子节信息的令牌是否是正确的，仅用于某些特殊的协议实现
Check whether the token of the current header subsection information is correct, only for some special protocol implementations

服务器关闭的时候需要做的事情
Things to do when the server is down

创建一个指定的异形客户端连接，使用Hsl协议来发送注册包
Create a specified profiled client connection and use the Hsl protocol to send registration packets

创建一个指定的异形客户端连接，使用Hsl协议来发送注册包
Create a specified profiled client connection and use the Hsl protocol to send registration packets

创建一个新的socket对象并连接到远程的地址，默认超时时间为10秒钟，需要指定ip地址以及端口号信息
Create a new socket object and connect to the remote address. The default timeout is 10 seconds. You need to specify the IP address and port number.

创建一个新的socket对象并连接到远程的地址，需要指定远程终结点，超时时间（单位是毫秒），如果需要绑定本地的IP或是端口，传入 local对象
To create a new socket object and connect to the remote address, you need to specify the remote endpoint, the timeout period (in milliseconds), if you need to bind the local IP or port, pass in the local object

创建一个新的socket对象并连接到远程的地址，需要指定ip地址以及端口号信息，还有超时时间，单位是毫秒
To create a new socket object and connect to a remote address, you need to specify the IP address and port number information, and the timeout period in milliseconds

创建一个新的socket对象并连接到远程的地址，默认超时时间为10秒钟，需要指定ip地址以及端口号信息
Create a new socket object and connect to the remote address. The default timeout is 10 seconds. You need to specify the IP address and port number.

创建一个新的socket对象并连接到远程的地址，需要指定远程终结点，超时时间（单位是毫秒），如果需要绑定本地的IP或是端口，传入 local对象
To create a new socket object and connect to the remote address, you need to specify the remote endpoint, the timeout period (in milliseconds), if you need to bind the local IP or port, pass in the local object

创建一个新的socket对象并连接到远程的地址，需要指定ip地址以及端口号信息，还有超时时间，单位是毫秒
To create a new socket object and connect to a remote address, you need to specify the IP address and port number information, and the timeout period in milliseconds

删除一个指定的文件，如果文件不存在，直接返回 True，如果文件存在则直接删除，删除成功返回 True，如果发生了异常，返回False
Delete a specified file, if the file does not exist, return True directly, if the file exists, delete it directly, if the deletion is successful, return True, if an exception occurs, return False

Determines whether the specified object is equal to the current object.

Allows an object to try to free resources and perform other cleanup operations before it is reclaimed by garbage collection.

Serves as the default hash function.

Gets the Type of the current instance.

Creates a shallow copy of the current Object.

接收固定长度的字节数组，允许指定超时时间，默认为60秒，当length大于0时，接收固定长度的数据内容，当length小于0时，接收不大于2048长度的随机数据信息
Receiving a fixed-length byte array, allowing a specified timeout time. The default is 60 seconds. When length is greater than 0, fixed-length data content is received. When length is less than 0, random data information of a length not greater than 2048 is received.

接收固定长度的字节数组，允许指定超时时间，默认为60秒，当length大于0时，接收固定长度的数据内容，当length小于0时，接收不大于2048长度的随机数据信息
Receiving a fixed-length byte array, allowing a specified timeout time. The default is 60 seconds. When length is greater than 0, fixed-length data content is received. When length is less than 0, random data information of a length not greater than 2048 is received.

接收固定长度的字节数组，允许指定超时时间，默认为60秒，当length大于0时，接收固定长度的数据内容，当length小于0时，buffer长度的缓存数据
Receiving a fixed-length byte array, allowing a specified timeout time. The default is 60 seconds. When length is greater than 0, fixed-length data content is received. When length is less than 0, random data information of a length not greater than 2048 is received.

接收固定长度的字节数组，允许指定超时时间，默认为60秒，当length大于0时，接收固定长度的数据内容，当length小于0时，buffer长度的缓存数据
Receiving a fixed-length byte array, allowing a specified timeout time. The default is 60 seconds. When length is greater than 0, fixed-length data content is received. When length is less than 0, random data information of a length not greater than 2048 is received.

[自校验] 接收一条完整的同步数据，包含头子节和内容字节，基础的数据，如果结果异常，则结束通讯
[Self-checking] Receive a complete synchronization data, including header subsection and content bytes, basic data, if the result is abnormal, the communication ends

[自校验] 接收一条完整的同步数据，包含头子节和内容字节，基础的数据，如果结果异常，则结束通讯
[Self-checking] Receive a complete synchronization data, including header subsection and content bytes, basic data, if the result is abnormal, the communication ends

接收固定长度的字节数组，允许指定超时时间，默认为60秒，当length大于0时，接收固定长度的数据内容，当length小于0时，接收不大于2048长度的随机数据信息
Receiving a fixed-length byte array, allowing a specified timeout time. The default is 60 seconds. When length is greater than 0, fixed-length data content is received. When length is less than 0, random data information of a length not greater than 2048 is received.

接收固定长度的字节数组，允许指定超时时间，默认为60秒，当length大于0时，接收固定长度的数据内容，当length小于0时，接收不大于2048长度的随机数据信息
Receiving a fixed-length byte array, allowing a specified timeout time. The default is 60 seconds. When length is greater than 0, fixed-length data content is received. When length is less than 0, random data information of a length not greater than 2048 is received.

接收固定长度的字节数组，允许指定超时时间，默认为60秒，当length大于0时，接收固定长度的数据内容，当length小于0时，buffer长度的缓存数据
Receiving a fixed-length byte array, allowing a specified timeout time. The default is 60 seconds. When length is greater than 0, fixed-length data content is received. When length is less than 0, random data information of a length not greater than 2048 is received.

接收固定长度的字节数组，允许指定超时时间，默认为60秒，当length大于0时，接收固定长度的数据内容，当length小于0时，buffer长度的缓存数据
Receiving a fixed-length byte array, allowing a specified timeout time. The default is 60 seconds. When length is greater than 0, fixed-length data content is received. When length is less than 0, random data information of a length not greater than 2048 is received.

接收一条完整的 数据内容，需要指定超时时间，单位为毫秒。
Receive a complete data content, Need to specify a timeout period in milliseconds

接收一条完整的 数据内容，需要指定超时时间，单位为毫秒。
Receive a complete data content, Need to specify a timeout period in milliseconds

[自校验] 从网络中接收一串字节数据，如果结果异常，则结束通讯
[Self-checking] Receive a string of byte data from the network. If the result is abnormal, the communication ends.

[自校验] 从网络中接收一串字节数据，如果结果异常，则结束通讯
[Self-checking] Receive a string of byte data from the network. If the result is abnormal, the communication ends.

接收一行命令数据，需要自己指定这个结束符，默认超时时间为60秒，也即是60000，单位是毫秒
To receive a line of command data, you need to specify the terminator yourself. The default timeout is 60 seconds, which is 60,000, in milliseconds.

接收一行命令数据，需要自己指定这个结束符，默认超时时间为60秒，也即是60000，单位是毫秒
To receive a line of command data, you need to specify the terminator yourself. The default timeout is 60 seconds, which is 60,000, in milliseconds.

接收一行命令数据，需要自己指定这个结束符，默认超时时间为60秒，也即是60000，单位是毫秒
To receive a line of command data, you need to specify the terminator yourself. The default timeout is 60 seconds, which is 60,000, in milliseconds.

接收一行命令数据，需要自己指定这个结束符，默认超时时间为60秒，也即是60000，单位是毫秒
To receive a line of command data, you need to specify the terminator yourself. The default timeout is 60 seconds, which is 60,000, in milliseconds.

[自校验] 从网络中接收一个文件，写入数据流，如果结果异常，则结束通讯，参数顺序文件名，文件大小，文件标识，上传人
[Self-checking] Receive a file from the network. If the result is abnormal, the communication ends.

[自校验] 从网络中接收一个文件，如果结果异常，则结束通讯
[Self-checking] Receive a file from the network. If the result is abnormal, the communication ends.

[自校验] 从网络中接收一个文件，写入数据流，如果结果异常，则结束通讯，参数顺序文件名，文件大小，文件标识，上传人
[Self-checking] Receive a file from the network. If the result is abnormal, the communication ends.

[自校验] 从网络中接收一个文件，如果结果异常，则结束通讯
[Self-checking] Receive a file from the network. If the result is abnormal, the communication ends.

[自校验] 从套接字中接收文件头信息
[Self-checking] Receive file header information from socket

[自校验] 从套接字中接收文件头信息
[Self-checking] Receive file header information from socket

接收一条hsl协议的数据信息，自动解析，解压，解码操作，获取最后的实际的数据，接收结果依次为暗号，用户码，负载数据
Receive a piece of hsl protocol data information, automatically parse, decompress, and decode operations to obtain the last actual data. The result is a opCode, user code, and payload data in order.

接收一条hsl协议的数据信息，自动解析，解压，解码操作，获取最后的实际的数据，接收结果依次为暗号，用户码，负载数据
Receive a piece of hsl protocol data information, automatically parse, decompress, and decode operations to obtain the last actual data. The result is a opCode, user code, and payload data in order.

使用MQTT协议从网络接收字节数组，然后写入文件或流中，支持进度报告
Use MQTT protocol to receive byte array from the network, and then write it to file or stream, support progress report

使用MQTT协议从网络接收字节数组，然后写入文件或流中，支持进度报告
Use MQTT protocol to receive byte array from the network, and then write it to file or stream, support progress report

接收一条完整的MQTT协议的报文信息，包含控制码和负载数据
Receive a message of a completed MQTT protocol, including control code and payload data

接收一条完整的MQTT协议的报文信息，包含控制码和负载数据
Receive a message of a completed MQTT protocol, including control code and payload data

接收一条完整的MQTT协议的报文信息，包含控制码和负载数据
Receive a message of a completed MQTT protocol, including control code and payload data

接收一条完整的MQTT协议的报文信息，包含控制码和负载数据
Receive a message of a completed MQTT protocol, including control code and payload data

使用MQTT协议从socket接收指定长度的字节数组，然后全部写入到流中，可以指定进度报告
Use the MQTT protocol to receive a byte array of specified length from the socket, and then write all of them to the stream, and you can specify a progress report

使用MQTT协议从socket接收指定长度的字节数组，然后全部写入到流中，可以指定进度报告
Use the MQTT protocol to receive a byte array of specified length from the socket, and then write all of them to the stream, and you can specify a progress report

从网络接收一条完整的redis报文的消息
Receive a complete redis message from the network

从网络接收一条完整的redis报文的消息
Receive a complete redis message from the network

接收一行基于redis协议的字符串的信息，需要指定固定的长度
Receive a line of information based on the redis protocol string, you need to specify a fixed length

接收一行基于redis协议的字符串的信息，需要指定固定的长度
Receive a line of information based on the redis protocol string, you need to specify a fixed length

[自校验] 从网络中接收一个字符串数组，如果结果异常，则结束通讯
[Self-check] Receive an array of strings from the network. If the result is abnormal, the communication ends.

[自校验] 从网络中接收一个字符串数组，如果结果异常，则结束通讯
[Self-check] Receive an array of strings from the network. If the result is abnormal, the communication ends.

[自校验] 从网络中接收一个字符串数据，如果结果异常，则结束通讯
[Self-checking] Receive a string of data from the network. If the result is abnormal, the communication ends.

[自校验] 从网络中接收一个字符串数据，如果结果异常，则结束通讯
[Self-checking] Receive a string of data from the network. If the result is abnormal, the communication ends.

发送消息给套接字，直到完成的时候返回，经过测试，本方法是线程安全的。
Send a message to the socket until it returns when completed. After testing, this method is thread-safe.

发送消息给套接字，直到完成的时候返回，经过测试，本方法是线程安全的。
Send a message to the socket until it returns when completed. After testing, this method is thread-safe.

发送消息给套接字，直到完成的时候返回，经过测试，本方法是线程安全的。
Send a message to the socket until it returns when completed. After testing, this method is thread-safe.

发送消息给套接字，直到完成的时候返回，经过测试，本方法是线程安全的。
Send a message to the socket until it returns when completed. After testing, this method is thread-safe.

[自校验] 直接发送字符串数组并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-check] Send string array directly and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

[自校验] 直接发送字符串数组并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-check] Send string array directly and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

发送消息给套接字，直到完成的时候返回，经过测试，本方法是线程安全的。
Send a message to the socket until it returns when completed. After testing, this method is thread-safe.

发送消息给套接字，直到完成的时候返回，经过测试，本方法是线程安全的。
Send a message to the socket until it returns when completed. After testing, this method is thread-safe.

发送消息给套接字，直到完成的时候返回，经过测试，本方法是线程安全的。
Send a message to the socket until it returns when completed. After testing, this method is thread-safe.

发送消息给套接字，直到完成的时候返回，经过测试，本方法是线程安全的。
Send a message to the socket until it returns when completed. After testing, this method is thread-safe.

[自校验] 发送字节数据并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-check] Send the byte data and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

[自校验] 发送字节数据并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-check] Send the byte data and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

[自校验] 发送字节数据并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-check] Send the byte data and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

[自校验] 发送字节数据并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-check] Send the byte data and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

[自校验] 将流数据发送至套接字，具体发送细节将在继承类中实现，如果结果异常，则结束通讯
[Self-checking] Send stream data to the socket. The specific sending details will be implemented in the inherited class. If the result is abnormal, the communication will be terminated

[自校验] 将文件数据发送至套接字，具体发送细节将在继承类中实现，如果结果异常，则结束通讯
[Self-checking] Send the file data to the socket. The specific sending details will be implemented in the inherited class. If the result is abnormal, the communication will end

[自校验] 将流数据发送至套接字，具体发送细节将在继承类中实现，如果结果异常，则结束通讯
[Self-checking] Send stream data to the socket. The specific sending details will be implemented in the inherited class. If the result is abnormal, the communication will be terminated

[自校验] 将文件数据发送至套接字，具体发送细节将在继承类中实现，如果结果异常，则结束通讯
[Self-checking] Send the file data to the socket. The specific sending details will be implemented in the inherited class. If the result is abnormal, the communication will end

[自校验] 将文件数据发送至套接字，如果结果异常，则结束通讯
[Self-check] Send the file data to the socket. If the result is abnormal, the communication is ended.

[自校验] 将文件数据发送至套接字，如果结果异常，则结束通讯
[Self-check] Send the file data to the socket. If the result is abnormal, the communication is ended.

向指定的通信对象发送字节数据

向指定的通信对象发送字符串数据

使用MQTT协议将一个数据流发送到网络上去，需要保存的文件名，可选指定文件描述信息，进度报告
Use the MQTT protocol to send a data stream to the network, the file name that needs to be saved, optional file description information, progress report

使用MQTT协议将一个文件发送到网络上去，需要指定文件名，保存的文件名，可选指定文件描述信息，进度报告
To send a file to the network using the MQTT protocol, you need to specify the file name, the saved file name, optionally specify the file description information, and the progress report

使用MQTT协议将一个数据流发送到网络上去，需要保存的文件名，可选指定文件描述信息，进度报告
Use the MQTT protocol to send a data stream to the network, the file name that needs to be saved, optional file description information, progress report

使用MQTT协议将一个文件发送到网络上去，需要指定文件名，保存的文件名，可选指定文件描述信息，进度报告
To send a file to the network using the MQTT protocol, you need to specify the file name, the saved file name, optionally specify the file description information, and the progress report

使用MQTT协议将流中的数据读取到字节数组，然后都写入到socket里面，可以指定进度报告，主要用于将文件发送到网络。
Use the MQTT protocol to read the data in the stream into a byte array, and then write them all into the socket. You can specify a progress report, which is mainly used to send files to the network.

使用MQTT协议将流中的数据读取到字节数组，然后都写入到socket里面，可以指定进度报告，主要用于将文件发送到网络。
Use the MQTT protocol to read the data in the stream into a byte array, and then write them all into the socket. You can specify a progress report, which is mainly used to send files to the network.

发送一个流的所有数据到指定的网络套接字，需要指定发送的数据长度，支持按照百分比的进度报告
Send all the data of a stream to the specified network socket. You need to specify the length of the data to be sent. It supports the progress report in percentage.

发送一个流的所有数据到指定的网络套接字，需要指定发送的数据长度，支持按照百分比的进度报告
Send all the data of a stream to the specified network socket. You need to specify the length of the data to be sent. It supports the progress report in percentage.

[自校验] 直接发送字符串数据并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-checking] Send string data directly and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

[自校验] 直接发送字符串数组并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-check] Send string array directly and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

[自校验] 直接发送字符串数据并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-checking] Send string data directly and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

[自校验] 直接发送字符串数组并确认对方接收完成数据，如果结果异常，则结束通讯
[Self-check] Send string array directly and confirm that the other party has received the completed data. If the result is abnormal, the communication ends.

关闭服务器的引擎
Shut down the server's engine

使用已经配置好的端口启动服务器的引擎
Use the configured port to start the server's engine

指定端口号来启动服务器的引擎
Specify the port number to start the server's engine

当客户端的socket登录的时候额外检查的操作，并返回操作的结果信息。
The operation is additionally checked when the client's socket logs in, and the result information of the operation is returned.

服务器启动时额外的初始化信息，可以用于启动一些额外的服务的操作。
The extra initialization information when the server starts can be used to start some additional service operations.

当客户端连接到服务器，并听过额外的检查后，进行回调的方法
Callback method when the client connects to the server and has heard additional checks

Returns a string that represents the current object.

从套接字中接收所有的数据然后写入到指定的流当中去，需要指定数据的长度，支持按照百分比进行进度报告
Receives all data from the socket and writes it to the specified stream. The length of the data needs to be specified, and progress reporting is supported in percentage.

从套接字中接收所有的数据然后写入到指定的流当中去，需要指定数据的长度，支持按照百分比进行进度报告
Receives all data from the socket and writes it to the specified stream. The length of the data needs to be specified, and progress reporting is supported in percentage.

当接收到字节数据的时候,触发此事件

当接收到文本数据的时候,触发此事件

对客户端而言是的通讯用的套接字，对服务器来说是用于侦听的套接字
A communication socket for the client, or a listening socket for the server

文件传输的时候的缓存大小，直接影响传输的速度，值越大，传输速度越快，越占内存，默认为100K大小
The size of the cache during file transfer directly affects the speed of the transfer. The larger the value, the faster the transfer speed and the more memory it takes. The default size is 100K.

获取当前对象的JSON格式表示的字符串。
Gets the string represented by the JSON format of the current object.